Linux ZFS NotesBy Dag, on December 22nd, 2016, tagged outdated November 21st, 2017
[Outdated, but kept for reference as some information may still apply]
Been playing around with ZFS. ZoL seems to be maturing along nicely and I thought it was worth a day of playing around with it and learn the basics. I don't think I'm ready to take the plunge yet with anything serious, but it's an interesting and very likable FS/LVM. It supposably supports 256 ZiB/Zebibytes.
My preferred test system: Debian 8. These are my notes.
In-General advice for running ZFS
- Have 8GB ECC RAM + 1GB for every additional 1TB of storage.
ECC RAM is preferred, but no more than any other system. Matt Ahrens, one of the ZFS founders at Sun Microsystems, now one of the founding members of OpenZFS, said in a forum post (2014):
"There's nothing special about ZFS that requires/encourages the use of ECC RAM more so than any other filesystem. If you use UFS, EXT, NTFS, btrfs, etc without ECC RAM, you are just as much at risk as if you used ZFS without ECC RAM. Actually, ZFS can mitigate this risk to some degree if you enable the unsupported ZFS_DEBUG_MODIFY flag (zfs_flags=0x10). This will checksum the data while at rest in memory, and verify it before writing to disk, thus reducing the window of vulnerability from a memory error. I would simply say: if you love your data, use ECC RAM. Additionally, use a filesystem that checksums your data, such as ZFS."
Installing ZFS and handy extras
# apt-get update # apt-get install lsb-release # apt-get install debian-zfs # wget http://archive.zfsonlinux.org/debian/pool/main/z/zfsonlinux/zfsonlinux_6_all.deb # dpkg -i zfsonlinux_6_all.deb # wget http://zfsonlinux.org/4D5843EA.asc -O - | apt-key add - # apt install linux-headers-$(uname -r) # apt-get install zfs-dkms zfsutils-linux zfs-initramfs parted ntfs-3g samba
List available drives to use (many ways to do this)
# lsblk There are 4 types of dev labels you can use with ZFS/zpool /dev/sdX : Best for development/test pools as names are not persistent. /dev/disk/by-id/: Nice for small systems with a single disk controller, allows to mix disks without import problem. /dev/disk/by-path/: Good for large pools as name describes the PCI bus number, enclosure name and port number. /dev/disk/by-vdev/: Best for large pools, but relies on having a /etc/zfs/vdev_id.conf file properly configured for your system.
Converting drives to GPT if they are bigger than 2TB (good to do anyway for drive-cleaning and consistency)
# parted /dev/<drive> mklabel gpt
Creating a simple Raid-0 pool with no redundancy
# zpool create -o ashift=12 mypool sde sdf sdg sdh (ashift=12 will force 4096 byte sectors instead of default auto detect).
Destroying a pool
# zpool destroy mypool
Checking the status of a pool
# zpool status mypool # zfs list # zpool status -x (Nice for script-checking general pool health)
Creating a Raid-1+0 (Raid-10) type pool
Mirror RAID-1 based. Fastest, but only 50% storage capacity: # zpool create -o ashift=12 mypool mirror sde sdf mirror sdg sdh RAIDZ based. Slower, but more capacity depending on number of drives per vdev: # zpool create -o ashift=12 mypool raidz1 sde sdf sdg raidz1 sdh sdi sdj raidz1 sdk sdl sdm raidz1 sdn sdo sdp Both these setups will stripe across vdevs and be faster than single big RAIDZ pools. RAID-0 (fastest) RAID-1 RAIDZ-1 RAIDZ-2 RAIDZ-3 (slowest) There are three different RAID-Z modes which distribute parity across the drives: RAID-Z1 (similar to RAID 5, allows one disk to fail), RAID-Z2 (similar to RAID 6, allows two disks to fail), RAID-Z3 (Also referred to as RAID 7 allows three disks to fail).
Adding another vdev to the pool
# zpool add -o ashift=12 mypool mirror sdg sdh
Checking pool IO activity
# zpool iostat -v
Scrubbing and rebuilding/resilver
# zpool scrub mypool # zpool scrub -s mypool (if you need to stop it) # zpool replace mypool sde sde (replace old missing drive with new, respectively) # zpool clear mypool (remove any no-longer-relevant error messages) It's recommended to scrub at least once a week.
Creating a file system / mounting point / dataset
# zfs create mypool/mypool1 # mkdir /mnt/mypoolstorage (optional) # zfs set mountpoint=/mnt/mypoolstorage mypool/mypool1 (optional) # zfs list # zfs destroy mypool/mypool1 You should only store data on these type of mounting points / datasets and not directly on the pool. This is because they will have their own sets of attributes that can be set.
Check automatic mounting on startup/shutdown
# nano /etc/default/zfs ZFS_MOUNT=’YES’ ZFS_UNMOUNT=’YES’
Check all configuration values
# zpool get all mypool # zfs get all mypool/<dataset>
# zpool set autoexpand=on mypool autoexpand: Must be set before replacing the first drive in your pool. Controls automatic pool expansion when the underlying LUN is grown. Default is "off". After all drives in the pool have been replaced with larger drives, the pool will automatically grow to the new size. This setting is a boolean, with values either "on" or "off".
Snapshots, Backups and Recovery
Creating a snapshot: # zfs snapshot mypool/mypool1@mandag (dataset) # zfs snapshot mypool@mandag (entire pool) # zfs list –t all (or just snapshot) Deleting a snapshot # zfs destroy mypool/mypool1@mandag # zfs destroy mypool@mandag Restoring data from snapshots # zfs rollback mypool/mypool1@mandag # zfs rollback mypool@mandag Make a backup to an image file # zfs send mypool/mypool1@mandag > /backup/mypool-mypool1.img # zfs send mypool@mandag > /backup/mypool.img (normal) # zfs send mypool@mandag | xz > /backup/mypool.img (compressed) # zfs send mypool@mandag | xz | openssl enc –aes-256-cbc –a –salt > /backup/mypool.img (with encryption) Recover from image file # zfs receive mypool/mypool1 < /backup/mypool-mypool1.img If compressed and encrypted # openssl enc -d -aes-256-cbc -a -in /backup/mypool-mypool1.img | unxz | zfs receive mypool/mypool1 Send and receive over SSH # zfs send mypool/mypool1@mandag | ssh firstname.lastname@example.org "zfs receive mypool/mypool1"
Sharing via Samba
# zfs create -o casesensitivity=mixed mypool/srv (to mimic Windows CI) # zfs set sharesmb=on mypool/srv # nano /etc/samba/smb.conf [Mypool1] comment = Debian ZFS Pool read only = no locking = no path = /mypool/mypool1 guest ok = no # smbpasswd –a <new_samba_user> # service samba reload Remember to set suitable user rights on shared folders.